Rinker 350/360 2007+ Random Topics

YYZRC · May 2022

I’m hoping to do the top in white - waiting for paint to arrive!

aero3113 · May 2022

Nice @YYZRC ! How did you secure the racks?

YYZRC · May 2022

Removed the seat back and used two 2.5” #10 stainless screws on each rack.

YYZRC · May 2022

The H3O+ works well.

oscar1 · May 2022

Awesome

aero3113 · May 2022

Very nice @YYZRC !!

oscar1 · May 2022

YYZRC:
You look ready for ICW cruise down to Florida

YYZRC · May 2022

New fridge is in. Now to build a new cabinet!

YYZRC · May 2022

Got the rear wash down receiver installed.

YYZRC · June 2022

aero3113 said:

Nice @YYZRC ! How did you secure the racks?

@aero3113 in case you decide to do this, make sure your notches are at least 45 degrees or the stuff will fall out when you open the engine hatch. I did 45 and it’s just barely steep enough.

aero3113 · June 2022

Thanks @YYZRC !!
Its on my list, will be great for my kayak and paddle board paddles.

YYZRC · June 2022

tricountytrail · June 2022

Any one have a part number or source for these hinges?

Image: https://us.v-cdn.net/5020499/uploads/editor/56/vwnegff3nj87.jpg

YYZRC · June 2022

New blower ducts finally.

Spyderweb · June 2022

Ooh, that looks nice.

aero3113 · June 2022

Nice @YYZRC , I did that when I first bought the 330. Are you going to put the water/sand diverters on the hatch?

aero3113 · June 2022

This is what the previous owner was running with!😳

YYZRC · June 2022

No, I hate those things. I was originally planning to do a PVC elbow and pipe to divert but have since decided to do nothing. I don’t put anything wet in the locker.

I ordered these for the inside of the locker:

aero3113 · June 2022

Nice

YYZRC · June 2022

I needed some replacement snap buttons that match the interior upholstery on my boat. These are perfect and should match any 2008 330/350.

https://www.greatlakesskipper.com/fasnap-boat-snap-buttons-btn30snap-rinker-white-3-8-inch-set-of-25

YYZRC · June 2022

Got the switch panel for the hardtop romance light installed. Included a USB charging port and the cig lighter port for inflating paddle boards.

aero3113 · June 2022

Nice @YYZRC !!

YYZRC · June 2022

I had two made, you want this one @aero3113 ?

YYZRC · June 2022

Added an extension to the stringer shelf so I can move around easier.

aero3113 · June 2022

YYZRC said:

I had two made, you want this one @aero3113 ?

No, but thanks! I’m thinking about putting in a USB socket somewhere near the aft seating area in the cockpit on the starboard side. I could just run a longer charging cord from the helm but obviously it would look cleaner with the USB socket.

YYZRC · June 2022

Cabinet is built and in. Waiting on the SS panel and trim.

YYZRC · June 2022

Found a nice faucet on Amazon Warehouse deals!

YYZRC · June 2022

Did the head faucet, too.

aero3113 · June 2022

Very nice @YYZRC , is it a direct swap since it only has the one hot/cold handle?

YYZRC · June 2022

Yep! Didn’t even need to enlarge either hole. This is much better for the skipper.

Howdy, Stranger!

Quick Links

Categories

Rinker 350/360 2007+ Random Topics

Comments