What did you do to your boat today

Comments

• rasbury Member Posts: 8,782 ✭✭✭✭✭

  April 2022

  They look good to me!

  0 · Share on FacebookShare on Twitter
• Ian Member Posts: 2,998 ✭✭✭✭

  April 2022 edited April 2022

  Put on my new switch covers today.
  
  From this:
  
  
  
  To this:
  
  
  

  Regards,

  Ian

  The Third “B”

  Ravena Coeymans Yacht Club

  https://www.rcyachtclub.com/

  4 · Share on FacebookShare on Twitter
• Grahamu Member Posts: 905 ✭✭✭

  April 2022

  Great upgrade, where did you get them?

  0 · Share on FacebookShare on Twitter
• Ian Member Posts: 2,998 ✭✭✭✭

  April 2022

  Newwire Marine. They are the Contrua XIV type not shown on website. Etched wasn’t going to work for me so called to ask about options and they offered these. Only Swim Platform was a special and they fit in Spreader as a full word, not Spreadr (or similar truncated).

  Regards,

  Ian

  The Third “B”

  Ravena Coeymans Yacht Club

  https://www.rcyachtclub.com/

  0 · Share on FacebookShare on Twitter
• Grahamu Member Posts: 905 ✭✭✭

  April 2022

  Thanks @Ian I have sent them an email.

  0 · Share on FacebookShare on Twitter
• boatman37 Member Posts: 810 ✭✭✭

  April 2022

  Brought it home from storage Thursday but haven't even pulled the cover yet. Been raining non-stop. But can't find a cone-clutch so will likely put the OD back on and limp it through this season. Also want to pull my newly installed windlass and re-seal it cause I know I didn't do a good job when I put it together. Other than that need to clean, buff and wax and thats it. But having had hernia surgery 6 weeks ago I get sore quick still so will take my time
  

  0 · Share on FacebookShare on Twitter
• rasbury Member Posts: 8,782 ✭✭✭✭✭

  April 2022 edited April 2022

  I guess one plus of Northern boating would be tge darned this is covered up 6 months are better...won't need as much buffing as mine does this season..never ending.

  0 · Share on FacebookShare on Twitter
• Pat310 Member Posts: 598 ✭✭✭

  April 2022

  Faded damaged boot stripe is gone

  0 · Share on FacebookShare on Twitter
• LaRea Member, Moderator Posts: 7,946 mod

  April 2022

  @Pat310 how much work was that, and how did you do it?  Mine is looking rough.  

  0 · Share on FacebookShare on Twitter
• LaRea Member, Moderator Posts: 7,946 mod

  April 2022

  Also, how the heck does the yard park boats that close together?  Must be a forklift rather than a travel-lift.

  0 · Share on FacebookShare on Twitter
• boatman37 Member Posts: 810 ✭✭✭

  April 2022

  boatman37 said:

  Brought it home from storage Thursday but haven't even pulled the cover yet. Been raining non-stop. But can't find a cone-clutch so will likely put the OD back on and limp it through this season. Also want to pull my newly installed windlass and re-seal it cause I know I didn't do a good job when I put it together. Other than that need to clean, buff and wax and thats it. But having had hernia surgery 6 weeks ago I get sore quick still so will take my time
  

  
  oops. forgot i have to re-install my seawater pump too. rebuilt it with a new housing and new impeller over winter. and install batteries. might have to get one of the kids to climb in there are i had hernia surgery 6 weeks ago. feel good and no restrictions but that house battery is heavy
  

  0 · Share on FacebookShare on Twitter
• aero3113 Member Posts: 9,602 ✭✭✭✭✭

  April 2022 edited April 2022

  @LaRea
  I used a decal eraser when I removed mine, simple and quick! I needed 2 erasers to remove all of my stripes on my 330.
  
  
  

  Post edited by aero3113 on April 2022

  2008 330EC

  0 · Share on FacebookShare on Twitter
• raybo3 Administrator Posts: 5,579 admin

  April 2022

  @LaRea boats being that close for winter storage is common. At my yard they use a big hydraulic trailer. 

  2002 342 Fiesta Vee PC Point Of Pines YC Revere MA. popyc.org     raybo3@live.com

  0 · Share on FacebookShare on Twitter
• Pat310 Member Posts: 598 ✭✭✭

  April 2022

  For the boot stripe I used heat gun plastic razor and acetone because of the close proximity to other boats. For top stripe I am using whizzy wheel under the cover like @aero3113 Definitely easier then heat gun. Took about 2 hrs each side for boot stripe

  0 · Share on FacebookShare on Twitter
• Pat310 Member Posts: 598 ✭✭✭

  April 2022 edited April 2022

  @LaRea Boats are stacked using a mobile crane

  1 · Share on FacebookShare on Twitter
• aero3113 Member Posts: 9,602 ✭✭✭✭✭

  April 2022

  @Pat310
  That picture looks very familiar!! 😂 Cramped with the shrink wrap on but doable!
  
  

  2008 330EC

  2 · Share on FacebookShare on Twitter
• Ian Member Posts: 2,998 ✭✭✭✭

  April 2022

  Where I store they get them a little closer, there’s very little between the rub rails. Getting to the stern is a near crawl on the floor. The yard manager has pushing in skills on the trailer rarely seen. Sadly he is the one injured in the explosion and fire in January. 

  Regards,

  Ian

  The Third “B”

  Ravena Coeymans Yacht Club

  https://www.rcyachtclub.com/

  0 · Share on FacebookShare on Twitter
• Ian Member Posts: 2,998 ✭✭✭✭

  April 2022

  Pat310 said:

  For the boot stripe I used heat gun plastic razor and acetone because of the close proximity to other boats. For top stripe I am using whizzy wheel under the cover like @aero3113 Definitely easier then heat gun. Took about 2 hrs each side for boot stripe

  As we have the same age and vessel I am keen to see if you have a shadow afterwards. Are you leaving off? I’d like to see end result photos to decide (or convince the admiral) to remove ours and not put back.

  Regards,

  Ian

  The Third “B”

  Ravena Coeymans Yacht Club

  https://www.rcyachtclub.com/

  0 · Share on FacebookShare on Twitter
• aero3113 Member Posts: 9,602 ✭✭✭✭✭

  April 2022 edited April 2022

  @Ian I’ve had it off for a season now, a slight shadow but barely noticeable now. I love the look without the stripes.
  
  
  

  2008 330EC

  0 · Share on FacebookShare on Twitter
• aero3113 Member Posts: 9,602 ✭✭✭✭✭

  April 2022

  @Ian for some reason my pics aren’t loading. If you scroll up you’ll see a pic of my boat with no stripes.

  2008 330EC

  0 · Share on FacebookShare on Twitter
• Pat310 Member Posts: 598 ✭✭✭

  April 2022

  @ian my photo wont load either.  I began buffing lower boot stripe area yesterday and was happy with the results. 3M heavy cut followed by 3M fine. Will post photo when I can

  0 · Share on FacebookShare on Twitter
• Pat310 Member Posts: 598 ✭✭✭

  April 2022

  Not a great pic. Buffed up to about 4” before the through hull. Looking down at it from the dock it wont be noticeable I’ll post again when I get to the top stripe 
  

  0 · Share on FacebookShare on Twitter
• Ian Member Posts: 2,998 ✭✭✭✭

  April 2022

  Thanks @Pat310 good to know. @aero3113 I had seen yours also before but you’re around 5-6 years newer and wondered if the extra time would leave more of a shadow or non-faded line.

  Regards,

  Ian

  The Third “B”

  Ravena Coeymans Yacht Club

  https://www.rcyachtclub.com/

  0 · Share on FacebookShare on Twitter
• Ian Member Posts: 2,998 ✭✭✭✭

  April 2022

  Came out of storage! Sanded the bottom ready to paint and taped ready to extend up at stern where she actually sits.
  
  
  

  Regards,

  Ian

  The Third “B”

  Ravena Coeymans Yacht Club

  https://www.rcyachtclub.com/

  1 · Share on FacebookShare on Twitter
• tricountytrail Member Posts: 230 ✭✭

  April 2022

  Pat310 said:

  For the boot stripe I used heat gun plastic razor and acetone because of the close proximity to other boats. For top stripe I am using whizzy wheel under the cover like @aero3113 Definitely easier then heat gun. Took about 2 hrs each side for boot stripe

  Anyone have a source for this Boot Stripe???
  Boat Stripe Actual 1/4" navy blue 1/4" metallic gold 1 1/4" navy blue Total 1 3/4" 
  
  

  0 · Share on FacebookShare on Twitter
• aero3113 Member Posts: 9,602 ✭✭✭✭✭

  April 2022 edited April 2022

  I did a quick look on eBay and found this. Not exactly what you’re looking for but I would call Great Lakes skipper (this seller) they have large stock of decals.
  
  https://www.ebay.com/itm/144484926868?mkcid=16&mkevt=1&mkrid=711-127632-2357-0&ssspo=PPsq0eSBQmO&sssrc=2349624&ssuid=jb9VSTJCQVS&var=&widget_ver=artemis&media=COPY
  

  2008 330EC

  0 · Share on FacebookShare on Twitter
• YYZRC Member Posts: 5,363 ✭✭✭✭✭

  April 2022

  I have a roll of the original blue/silver that I bought from Rinker just before they closed up. 

  2008 350 EC on Georgian Bay

  0 · Share on FacebookShare on Twitter
• Pat310 Member Posts: 598 ✭✭✭

  April 2022

  What I was going to do if I wanted to replace was 2” black and add 1/4” gold over top. I believe that’s how the original was made.  Seemed thicker when removing where the gold stripe was. 

  0 · Share on FacebookShare on Twitter
• SimcoeRinker400 Member Posts: 338 ✭✭✭

  April 2022

  My boat someone removed the upper deck line and which I find makes the boat look newer.

  2008 Rinker 400 EC 
  2015 Scarab 165G
  Laser Sailboat
  2002 Seadoo Explorer
  2023 Seadoo Spark Trixx x 2

  1 · Share on FacebookShare on Twitter
• Ian Member Posts: 2,998 ✭✭✭✭

  April 2022

  Friday 1st coat, 2nd yesterday, drives and tape removal today.
  
  

  Regards,

  Ian

  The Third “B”

  Ravena Coeymans Yacht Club

  https://www.rcyachtclub.com/

  5 · Share on FacebookShare on Twitter