What did you do to your boat today

Comments

• rmfriday Member Posts: 104 ✭✭

  April 2022

  
  

  7 · Share on FacebookShare on Twitter
• rmfriday Member Posts: 104 ✭✭

  April 2022

  Launched today!
  the marina finished putting the docks in today and we followed them with the 342 

  1 · Share on FacebookShare on Twitter
• YYZRC Member Posts: 5,370 ✭✭✭✭✭

  April 2022

  Life lesson: ablative paint doesn't wash off your skin easily.  If, however, you decide to enjoy some KFC after your ablative paint session, your hands will be clean in no time!

  2008 350 EC on Georgian Bay

  2 · Share on FacebookShare on Twitter
• mattie Member Posts: 1,322 ✭✭✭✭

  April 2022

  KFC is amazing stuff. 
  
  
  
  

  246BR, 276BR, H310BR current

  1 · Share on FacebookShare on Twitter
• skennelly Member Posts: 2,196 ✭✭✭✭

  April 2022

  Kentucky Fried Chicken?  

  2002 - 270FV Mag 350 B3

  0 · Share on FacebookShare on Twitter
• Ian Member Posts: 3,028 ✭✭✭✭

  April 2022

  YYZRC said:

  Life lesson: ablative paint doesn't wash off your skin easily.  If, however, you decide to enjoy some KFC after your ablative paint session, your hands will be clean in no time!

  If you use water washable it does…

  Regards,

  Ian

  The Third “B”

  Ravena Coeymans Yacht Club

  https://www.rcyachtclub.com/

  0 · Share on FacebookShare on Twitter
• mattie Member Posts: 1,322 ✭✭✭✭

  April 2022

  skennelly said:

  Kentucky Fried Chicken?  

  @YYZRC - hilarious.
  
  Doesn't matter what you get stuck on your hands....bondo, paint, primer, caulking - it all comes off once you eat KFC.
  
  Unfortunately you are ingesting it. lol.
  
  
  
  

  246BR, 276BR, H310BR current

  0 · Share on FacebookShare on Twitter
• YYZRC Member Posts: 5,370 ✭✭✭✭✭

  April 2022

  mattie said:

  @YYZRC - hilarious.
  
  Doesn't matter what you get stuck on your hands....bondo, paint, primer, caulking - it all comes off once you eat KFC.
  
  Unfortunately you are ingesting it. lol.
  
  

  Wait, which is the unfortunate part? Ingesting the ablative or the “chicken”?!

  2008 350 EC on Georgian Bay

  2 · Share on FacebookShare on Twitter
• TonyG13 Member Posts: 1,418 ✭✭✭✭

  April 2022

  Installed a grab bar at the helm today.
  
  In rougher seas instead of just holding onto the wheel, I can now widen my stance and have one hand on the wheel and one on the bar to keep more stable.
  
  Super easy: Just pulled the MFD, found a good flat spot, drilled and feathered the holes, put in oversized washers for backing, and lots of 3M clear marine silicone caulk...
  
  
  
  
  
  

  6 · Share on FacebookShare on Twitter
• Dream_Inn Member, Moderator Posts: 7,873 mod

  April 2022

  Tony, that bar looks great and I'm sure will get used more than you might think.
  

  Dream 'Inn III -- 2008 400 Express

  0 · Share on FacebookShare on Twitter
• aero3113 Member Posts: 9,678 ✭✭✭✭✭

  April 2022

  I agree, it looks great and will come in use. I’ve thought about adding a grab handle under the arch to help with getting down from the bow.
  

  2008 330EC

  0 · Share on FacebookShare on Twitter
• LaRea Member, Moderator Posts: 8,013 mod

  April 2022

  That's a smart mod.  Well done.

  0 · Share on FacebookShare on Twitter
• TonyG13 Member Posts: 1,418 ✭✭✭✭

  April 2022

  Thanks all - I've been wanting to do this for a couple of seasons, just finally got the cahonies to drill into the helm without screwing it up, and it took all of about 15 minutes. Should have done it sooner. 

  1 · Share on FacebookShare on Twitter
• YYZRC Member Posts: 5,370 ✭✭✭✭✭

  April 2022

  I made up some templates out of transparent vinyl so that I could center the plates perfectly over the hardtop access holes. You know, in case @aero3113 stops in for an inspection.  

  
  

  
  

  2008 350 EC on Georgian Bay

  1 · Share on FacebookShare on Twitter
• aero3113 Member Posts: 9,678 ✭✭✭✭✭

  April 2022 edited April 2022

  YYZRC said:

  I made up some templates out of transparent vinyl so that I could center the plates perfectly over the hardtop access holes. You know, in case @aero3113 stops in for an inspection.  

  
  

  
  

  
  

  2008 330EC

  3 · Share on FacebookShare on Twitter
• mattie Member Posts: 1,322 ✭✭✭✭

  April 2022

  YYZRC said:

  I made up some templates out of transparent vinyl so that I could center the plates perfectly over the hardtop access holes. You know, in case @aero3113 stops in for an inspection.  

  
  

  Very OCD - which I prefer. 

  
  

  “The way you do anything - is the way you do everything”
  
  
  
  
  

  246BR, 276BR, H310BR current

  1 · Share on FacebookShare on Twitter
• aero3113 Member Posts: 9,678 ✭✭✭✭✭

  April 2022

   

  I cut some shrink wrap off and waxed the hull.
  
  
  

  2008 330EC

  1 · Share on FacebookShare on Twitter
• diggin2day1 Member Posts: 1,331 ✭✭✭✭

  April 2022

  aero3113 said:

   

  I cut some shrink wrap off and waxed the hull.
  
  
  

  C’mon man… cut it off and let’s go!! Flowers are blooming, sun is shining… it’s was a balmy 38 degrees this morning… 

  2 · Share on FacebookShare on Twitter
• Pat310 Member Posts: 601 ✭✭✭

  April 2022

  @ian here you go. 3M heavy cut 3M fine and a coat of jescar power lock+from certain angles you can see a very very faint difference 

  0 · Share on FacebookShare on Twitter
• aero3113 Member Posts: 9,678 ✭✭✭✭✭

  April 2022

  LoL @diggin2day1 !! I would be in but my marina doesn’t allow boats in until the second weekend of May ! 🤷🏻‍♂️

  2008 330EC

  0 · Share on FacebookShare on Twitter
• diggin2day1 Member Posts: 1,331 ✭✭✭✭

  April 2022 edited April 2022

  @aero3113 - wow!! I’m looking to splash next week… if I had more free time I would’ve been in 3 weeks ago. 

  0 · Share on FacebookShare on Twitter
• Ian Member Posts: 3,028 ✭✭✭✭

  April 2022

  I am Monday yay! Full on final prep day tomorrow 
  
  

  Regards,

  Ian

  The Third “B”

  Ravena Coeymans Yacht Club

  https://www.rcyachtclub.com/

  1 · Share on FacebookShare on Twitter
• Ian Member Posts: 3,028 ✭✭✭✭

  May 2022

  Finally all buffed and bottom paint touched up from the repaint. Back tomorrow to put up canvas and set lines and fenders ready for splash.

  Regards,

  Ian

  The Third “B”

  Ravena Coeymans Yacht Club

  https://www.rcyachtclub.com/

  0 · Share on FacebookShare on Twitter
• goalie59 Member Posts: 349 ✭✭✭

  May 2022

  installed my repitched props done by Kawartha propeller. Hoping for decreased engine load and gallons per hour . 
  

  2 · Share on FacebookShare on Twitter
• YYZRC Member Posts: 5,370 ✭✭✭✭✭

  May 2022

  Gorgeous!

  2008 350 EC on Georgian Bay

  0 · Share on FacebookShare on Twitter
• Ian Member Posts: 3,028 ✭✭✭✭

  May 2022

  Launched and home!
  
  

  Regards,

  Ian

  The Third “B”

  Ravena Coeymans Yacht Club

  https://www.rcyachtclub.com/

  5 · Share on FacebookShare on Twitter
• Dream_Inn Member, Moderator Posts: 7,873 mod

  May 2022

  @goalie59 what's the size of those props?  I'm just curious.  My B-2 drives, I have 19.5" dia 4 blades. 
  

  Dream 'Inn III -- 2008 400 Express

  0 · Share on FacebookShare on Twitter
• Pat310 Member Posts: 601 ✭✭✭

  May 2022

  Ian said:

  Launched and home!
  
  
  

  I guess the admiral won. I see the stripes are still there!!!  LOL

  0 · Share on FacebookShare on Twitter
• Rinker310_LI Member Posts: 22 ✭

  May 2022

  today, I ripped out the old marinAIR unit and installed a new HVAC system by Webasto in my 310 .  What a difference , super quiet !  Also replaced the old ducting.  
  
  
  
  
  
  
  

  2002 Rinker 310

  6 · Share on FacebookShare on Twitter
• Ian Member Posts: 3,028 ✭✭✭✭

  May 2022

  Pat310 said:

  Ian said:

  Launched and home!
  
  
  

  I guess the admiral won. I see the stripes are still there!!!  LOL

  Actually didn’t discuss much, was too busy doing bottom paint and buffing and didn’t need another task!

  Regards,

  Ian

  The Third “B”

  Ravena Coeymans Yacht Club

  https://www.rcyachtclub.com/

  0 · Share on FacebookShare on Twitter