What did you do to your boat today

18182848687141

Comments

  • rmfridayrmfriday Member Posts: 106 ✭✭
    Launched today!
    the marina finished putting the docks in today and we followed them with the 342 
  • YYZRCYYZRC Member Posts: 5,400 ✭✭✭✭✭
    Life lesson: ablative paint doesn't wash off your skin easily.  If, however, you decide to enjoy some KFC after your ablative paint session, your hands will be clean in no time!
    2006 390 EC
    2008 350 EC
    Georgian Bay
  • mattiemattie Member Posts: 1,322 ✭✭✭✭
    KFC is amazing stuff. 



    246BR, 276BR, H310BR current
  • skennellyskennelly Member Posts: 2,196 ✭✭✭✭
    Kentucky Fried Chicken?  
    2002 - 270FV Mag 350 B3
  • IanIan Member Posts: 3,057 ✭✭✭✭✭
    YYZRC said:
    Life lesson: ablative paint doesn't wash off your skin easily.  If, however, you decide to enjoy some KFC after your ablative paint session, your hands will be clean in no time!
    If you use water washable it does…

    Regards,

    Ian

    The Third “B”

    Ravena Coeymans Yacht Club

    https://www.rcyachtclub.com/

  • mattiemattie Member Posts: 1,322 ✭✭✭✭
    skennelly said:
    Kentucky Fried Chicken?  
    @YYZRC - hilarious.

    Doesn't matter what you get stuck on your hands....bondo, paint, primer, caulking - it all comes off once you eat KFC.

    Unfortunately you are ingesting it. lol.



    246BR, 276BR, H310BR current
  • YYZRCYYZRC Member Posts: 5,400 ✭✭✭✭✭
    mattie said:
    @YYZRC - hilarious.

    Doesn't matter what you get stuck on your hands....bondo, paint, primer, caulking - it all comes off once you eat KFC.

    Unfortunately you are ingesting it. lol.

    Wait, which is the unfortunate part? Ingesting the ablative or the “chicken”?!
    2006 390 EC
    2008 350 EC
    Georgian Bay
  • Dream_InnDream_Inn Member, Moderator Posts: 7,919 mod
    Tony, that bar looks great and I'm sure will get used more than you might think.

    Dream 'Inn III -- 2008 400 Express

  • aero3113aero3113 Member Posts: 9,760 ✭✭✭✭✭
    I agree, it looks great and will come in use. I’ve thought about adding a grab handle under the arch to help with getting down from the bow.
    2008 330EC
  • LaReaLaRea Member, Moderator Posts: 8,059 mod
    That's a smart mod.  Well done.
  • TonyG13TonyG13 Member Posts: 1,438 ✭✭✭✭
    Thanks all - I've been wanting to do this for a couple of seasons, just finally got the cahonies to drill into the helm without screwing it up, and it took all of about 15 minutes. Should have done it sooner. 
  • YYZRCYYZRC Member Posts: 5,400 ✭✭✭✭✭
    I made up some templates out of transparent vinyl so that I could center the plates perfectly over the hardtop access holes. You know, in case @aero3113 stops in for an inspection.  


    2006 390 EC
    2008 350 EC
    Georgian Bay
  • aero3113aero3113 Member Posts: 9,760 ✭✭✭✭✭
    edited April 2022
    YYZRC said:
    I made up some templates out of transparent vinyl so that I could center the plates perfectly over the hardtop access holes. You know, in case @aero3113 stops in for an inspection.  



    2008 330EC
  • mattiemattie Member Posts: 1,322 ✭✭✭✭
    YYZRC said:
    I made up some templates out of transparent vinyl so that I could center the plates perfectly over the hardtop access holes. You know, in case @aero3113 stops in for an inspection.  

    Very OCD - which I prefer. 

    “The way you do anything - is the way you do everything”




    246BR, 276BR, H310BR current
  • aero3113aero3113 Member Posts: 9,760 ✭✭✭✭✭
     
    I cut some shrink wrap off and waxed the hull.


    2008 330EC
  • diggin2day1diggin2day1 Member Posts: 1,331 ✭✭✭✭
    aero3113 said:
     
    I cut some shrink wrap off and waxed the hull.


    C’mon man… cut it off and let’s go!! Flowers are blooming, sun is shining… it’s was a balmy 38 degrees this morning… 
  • Pat310Pat310 Member Posts: 603 ✭✭✭
    @ian here you go. 3M heavy cut 3M fine and a coat of jescar power lock+from certain angles you can see a very very faint difference 
  • aero3113aero3113 Member Posts: 9,760 ✭✭✭✭✭
    LoL @diggin2day1 !! I would be in but my marina doesn’t allow boats in until the second weekend of May ! 🤷🏻‍♂️
    2008 330EC
  • diggin2day1diggin2day1 Member Posts: 1,331 ✭✭✭✭
    edited April 2022
    @aero3113 - wow!! I’m looking to splash next week… if I had more free time I would’ve been in 3 weeks ago. 
  • IanIan Member Posts: 3,057 ✭✭✭✭✭
    I am Monday yay! Full on final prep day tomorrow 

    Regards,

    Ian

    The Third “B”

    Ravena Coeymans Yacht Club

    https://www.rcyachtclub.com/

  • IanIan Member Posts: 3,057 ✭✭✭✭✭
    Finally all buffed and bottom paint touched up from the repaint. Back tomorrow to put up canvas and set lines and fenders ready for splash.

    Regards,

    Ian

    The Third “B”

    Ravena Coeymans Yacht Club

    https://www.rcyachtclub.com/

  • goalie59goalie59 Member Posts: 356 ✭✭✭
    installed my repitched props done by Kawartha propeller. Hoping for decreased engine load and gallons per hour . 
  • YYZRCYYZRC Member Posts: 5,400 ✭✭✭✭✭
    Gorgeous!
    2006 390 EC
    2008 350 EC
    Georgian Bay
  • Dream_InnDream_Inn Member, Moderator Posts: 7,919 mod
    @goalie59 what's the size of those props?  I'm just curious.  My B-2 drives, I have 19.5" dia 4 blades. 

    Dream 'Inn III -- 2008 400 Express

  • Pat310Pat310 Member Posts: 603 ✭✭✭
    Ian said:
    Launched and home!


    I guess the admiral won. I see the stripes are still there!!!  LOL
  • IanIan Member Posts: 3,057 ✭✭✭✭✭
    Pat310 said:
    Ian said:
    Launched and home!


    I guess the admiral won. I see the stripes are still there!!!  LOL
    Actually didn’t discuss much, was too busy doing bottom paint and buffing and didn’t need another task!

    Regards,

    Ian

    The Third “B”

    Ravena Coeymans Yacht Club

    https://www.rcyachtclub.com/

Sign In or Register to comment.